Heat Surge Electric Fireplace Troubleshooting [7 Easy Solutions]
Heat Surge electric fireplaces assist you to feel warmth and comfort at a reasonable cost. But it’ll be a troublemaker after stopping work like shutting off, flames going out, no heat from the fireplace, blowing cold air, etc.
Whatever your fireplace issue, now let’s find the solution from our Heat Surge electric fireplace troubleshooting guide to solve your fireplace problem.
Table of Contents
- Heat Surge Electric Fireplace Troubleshooting [7 Easy Solutions]
- 1. Heating Unit Turns Off
- 2. Flame Without Heat
- 3. The Fireplace Not Bright Enough
- 4. Producing Excessive Noise
- 5. Fireplace Flame Effect Not Working
- 6. The Power Cord Becomes Warm
- 7. Circuit Breakers Flipping
- FAQ:
- Why does there a jumpy flame on the electric fireplace?
- Why does EC show on an electric-powered fireplace?
- Why is the electric fireplace waving cold air?
- Where is the light bulb in an electric fireplace?
- How lengthy do electric-powered fireplaces ultimate?
- Can electric-powered fireplaces seize the fire?
- What is the reason for shaky flame and light in movement?
- Bottom Line:
Heat Surge Electric Fireplace Troubleshooting [7 Easy Solutions]
Heat surge electric fireplaces can irregularly fail or break down like other electric appliances. Here we have enlisted 7 easy solutions that’ll help to troubleshoot your electric fireplace.
1. Heating Unit Turns Off
Some of the reasons for the shutting down of an electric fireplace are overheating the unit, restricted airflow, reaching the temperature setting, blocking the heater outlet, dirty elements, and using incorrect bulbs.
Solution:
- Verify the power cord is connected to an electric socket
- Follow the instructions properly
- Remove the obstructions that block airflow
- Check the installed filter for cleanness & blockage
- Tap the reset button placed on the top left zone of the back of the appliance
- Unplug for 10 minutes, then retry
- Examine the housebreaker
2. Flame Without Heat
Heat may not be circulated for the wrong thermostat setting or if the heater control button is off.
Solution:
- Set the thermostat entirely proper or high
- Check the high heat or low heat button is on
3. The Fireplace Not Bright Enough
It could be a straightforward case of disconnected or loose light bulbs.
Solution:
- Check unit is obstructed in and became on
- Confirm light bulbs are attached tight and not burned out
- Make sure the flame has not been attenuated by utilizing controls
4. Producing Excessive Noise
This problem usually occurs when the flame tube is in a faulty position, or dirty motor, or the damaged control panel of flame speed.
Solution:
- Unplug the fireside from the electric outlet
- Let cool the light bulbs for 15 minutes
- Detach the bottom cover of the fireplace by removing the two screws
- Hold the left quit of the flame tube displayed on the left and press upward till the pole of the tube is placed into the chamber that is positioned in the middle of the bracket
- Replace the decrease in the front cowl
- Plug the hearth into the electric outlet
- Turn the fireplace on
5. Fireplace Flame Effect Not Working
Don’t get the flame effect in your electric fireplace? Then, the culprit behind the issue could be the burning out of the bulbs or a defective flame rod.
Solution:
- Disconnect the power of the fireplace
- Open the excess cover on the back of the fireplace unit
- Make a replacement of the bulb(s) when they are burnt out
- In case the motor that runs the rod fails to work, restore the motor if manageable
- When the flame acts are squeaking at working, make the rod slippery
6. The Power Cord Becomes Warm
Heaters are regarded as high-draw applications, and small amounts of the warmth of the cable are customary and acceptable. Damaged outlets are responsible for heat and high resistance. If it is not touchable, you’ll have a problem.
Solution:
- Unplug the cord
- Try to put it in another outlet
- If it is not working, call an electrician to overlook the outlet
7. Circuit Breakers Flipping
This can happen if there is any kind of short circuit on the wire.
Solution:
- Check the circuit is not plugged into other appliances
- Do not use surge protectors, power strips, or short addition cords
- Plugged on another circuit
- Install a staunch outlet
This site is proudly sponsored by Innovacious.com
Let us build and manage the website of your dreams!
